Global SpillDB4G

Step 1 - Decide Where To InstallDecide where you want to install the lasfit rock light.Step 2 - Drill Mounting HolesDrill suitable mounting holes at the mounting location.Step 3 - Drill The Wire HolesIf you want to hide the wiring, line up the light with the hole you just drilled, and drill an additional hole in place to run the wire through the mounting surface. Otherwise, the wiring needs to be pulled aside.(Below is the wiring diagram)

AccessoriesMounting VideoMounting InstructionsEffect Picture After InstallationQuestions About the Installation?Where Can I Buy Lasfit Rock Lights?

White coloured cabinets should only be used for storing waste flammable liquids (205L drum). This is because emergency services need the distinctive colour coding on the different cabinet types so they can instantly identify what chemicals are in storage.

Global spillsigns

At Lasfit, we use manufacturer names, symbols, and descriptions in our visuals and descriptions purely to help customers recognize products easily. It is neither inferred nor implied that our products are endorsed by or affiliated with the vehicle manufacturers shown on this page.

If you are going to use Lasfit rock light to upgrade your vehicle, please click the link below or log in to our LASFIT official webpage to choose.

Global spilldrip tray

Global spillcontrol

Step 4 - Install The Rock LightInstall the light using the included nuts, bolts and washers as shown in the picture below.

© 2024 Area Safe Products Pty Ltd. All rights reserved. All prices shown are Australian Dollars and exclude GST.Digital Agency Sydney

The following installation guide will give you basic instructions on how to install and connect the Lasfit Rock Light Series Kit. Please disconnect the power before starting the installation.

While we believe we offer the best value for money offer in Australia, we do also promise to match or better any lower price on the equivalent product*.Let us know today what we can do to help you get the best value for money:

Step 5 - Install With Zip Ties（Optional）You can also use zip ties to mount the rock light to any available connection point, there are tabs on each side of the light.Step 6 - Switch WiringDetermine a suitable location to mount the switch, close to the battery or mains terminals. Route the switch wiring to this location.Step 7 - Connect The BatteryConnect the input wire to the positive battery. Connect the ground wire to the negative terminal of the battery or the original factory ground point.

Global SPILL and safetyABN

According to Australian Standards, an Emergency eyewash, emergency shower and a spill kit must be installed in the area where hazardous substances are stored, opened, handled and prepared.

Global Spillperth

The Lasfit rock light has been strictly tested and is officially launched! Switch to white or amber with just one touch, no need to change filters or use complicated Bluetooth APP, perfect for any weather conditions! If you're looking for a game-changing off-road adventure, the Lasfit Switchback Rock Lights are sure to take your off-road experience to the next level! Designed for the off-road enthusiast, these high-performance lights feature a power output of 6 watts per pod and a 110° optical angle, making them the perfect addition to any truck, JEEP or SUV.

It is dangerous to store different categories of chemical together and it is dangerous (and against the law) to store more than a very small quantity of chemicals without an Australian Standard approved storage cabinet. For safe storage of chemical containers, Area Safe dangerous goods cabinets should be purchased.

Step 8 - Select Switch LocationDetermine a suitable location to mount the switch in the cab of the vehicle.Route the switch wiring to this location. This may require going through the vehicle firewall. We recommend following the path of the original factory wiring harness and unplugging the switch while routing.Step 9 - Install The SwitchDrill a hole or mount the switch to anywhere you want. and install the switch. Reconnect the wires to the switch.Step 10 - Routing Extension WiresDetermine which extension cords and splitters are included in the kit. Route extension wires to each LED, keeping any moving parts out of direct contact with heat sources. Following the original factory arrangement is best practice.Step 11 - Reconnect The BatteryReconnect the negative terminal of the battery and test. Secure any excess or loose wiring.