Lock Box · RS232 to USB Converter Cable · 003 Key Switches, Locks and Padlocks · Push Buttons, Switches & LED's · IP65 and IP66 ABS Enclosures · Gas Panel ...

EX2 allows for a tool-free custom look to your driving lights and light bars with 8 interchangeable trim colour options: Slate (Grey), Stealth (Black), Sunburst ...

This product has shipping restrictions, so it might have limited shipping options or cannot be shipped to the following countries:

Question: So i understand that the two silver leads are the actual switch circuit and the gold goes to ground for the LED. However, i'm wanting to use a higher source voltage (24-30VDC). Still a bit of an electronics noob, but can i do a voltage divider (put a resistor between the gold and ground) to reduce the voltage across the LED down to 12V?

Skill Level: Competent - You will be required to reference a datasheet or schematic to know how to use a component. Your knowledge of a datasheet will only require basic features like power requirements, pinouts, or communications type. Also, you may need a power supply that?s greater than 12V or more than 1A worth of current. See all skill levels

These panel-mounting rocker switches have built-in indicator lights to let you know when your switch is engaged. They mount into a 20.2mm diameter hole and are rated up to 16A @ 12v. These simple SPST on-off switches have three terminals, the two that you would normally see plus a ground tab for the blue LED lamp inside. Although these are rated for 12v, the LED works with as little as 5V.

Here's how to wire this, based on my own trial and error just now. Power into the switch goes to the silver pin on the end (opposite the gold pin). Power to your project goes from the center (silver) pin. Ground goes to the gold pin. This allows the LED and the project to be powered on and off correctly. Ground only goes to this switch because of the LED. On the two-pin (non-LED) version of this switch, ground would just go directly to your project and the switch would have power-in on one pin and power-out on the other.

Does anybody have accurate dimensions for this switch? Obviously the diameter is slightly lather than 20.2mm, but what is the length from the bottom of the terminals to the bottom of the large plastic ring (where is would sit flush against a surface)?

Rated to 4500kgs. Lightweight Approximately 925kgs (allows up 3578kgs of house to be built on trailer). Hot Dip Galvanized for A1 Rust Protection.

Basically, the first two terminals are just connected to the SPST switch contacts, and the LED anode (and resistor) is connected to one side of the switch, with the LED cathode connected to the third terminal which you connect to ground. It's gold plated so you know this is the "odd" terminal which is not connected to the switch.

This switch appears to have three terminals, from the photos.Therefore, I assume that it works just like your common sort of illuminated power switch of this type.Two of the terminals are silver, and one of them is gold.The gold one connects to ground, the first silver one connects to your 12V supply (or 5-12V, but not higher, because the resistor in series with the LED internally is designed for 12V) and the second silver terminal connects to your load +12V rail.Basically, the first two terminals are just connected to the SPST switch contacts, and the LED anode (and resistor) is connected to one side of the switch, with the LED cathode connected to the third terminal which you connect to ground. It's gold plated so you know this is the "odd" terminal which is not connected to the switch.

3 Tonne light commercial tray L:4.2MW:2.3M 3 pallets Towbar (24V) Drop sides Manual & Automatic available Drive on a C Class Licence Call now to organise a ...

Starpad - White (3 sizes) · 30watt LED · approx 2600 Lumens · Length - 204mm · Height - 207mm · Width - 36mm.

We also manufacture our own range of compounds and private label products in our state-of-the-art plant located in sunny Queensland.

The gold one connects to ground, the first silver one connects to your 12V supply (or 5-12V, but not higher, because the resistor in series with the LED internally is designed for 12V) and the second silver terminal connects to your load +12V rail.

Proudly Australian owned and operated. We offer the largest range of tools and supplies - Online & In-Store with 4 trade centres and warehouses across Australia.

Oil & Fuel Workplace Spill Kit uses hydrophobic sorbents to repel water. Ideal for outdoor use in environments prone to oil and fuel contamination.

In this paper, a whip/stub antenna design is presented that utilizes an additional matching circuit to manipulate the coupling between the whip and stub in ...

If it requires power, you need to know how much, what all the pins do, and how to hook it up. You may need to reference datasheets, schematics, and know the ins and outs of electronics.

Dimensions: 227 x 221 x 52 · Watts 54 watts · Weighs 1.7kg · Power 24 Volts · Tails: 2 x 500mm Tails (1 male & 1 female) · Powder-coated or Stainless steel ...

Our innovative Super-Drive reflectors system delivers unmatched light intensity at the mid to long range.

Watching the video this switch is very easy to use. The led is very bright. my only negative if you could even consider it that is that the switch takes a good amount of force to switch so take that into consideration when mounting.

Far reaching spot to see ahead combined with a flood beam on the side to light up the ditches! ECE R112 certified for auxiliary driving beam.

We welcome your comments and suggestions below. However, if you are looking for solutions to technical questions please see our Technical Assistance page.